mgret.blogg.se

1. DD WRT V24 SP2 BRIDGE SETUP INSTALL
2. DD WRT V24 SP2 BRIDGE SETUP MOD
3. DD WRT V24 SP2 BRIDGE SETUP SOFTWARE

(be sure to turn off local DHCP & whatnot, you would be getting those settings from your neighbor's wifi)Īnd if you want to get fancy, once you have the Asus working in Wireless Client Mode just buy a 2nd wireless router & connect its LAN port (or use the WAN port if you don't mind double NATing) to the Asus' LAN port. Keep in mind Tomato does not support wireless repeater bridge mode (AFAIK).īut thinking about this more, w/ Tomato you could just set it in Wireless Client Mode & then just connect your machines via the LAN ports. This is assuming DD-WRT enables its DHCP server by default. (or, after 10-15 mins from successful transfer of the flash, change your computer's IP to DHCP & also power-cycle the router & see if your computer gets an IP address). It's possible the flash was successful but your computer lost its connection to the router so you can't tell if it's good or bad. After waiting at least 10 mins, try setting your IP config back to DHCP (no more 192.168.1.12, should be back to automatic DHCP). In step 4, after you get the OK message, did you wait at least 10 mins? It really does take about that long. Between step 1 & 2 (or really, even before step 1), you did connect an ethernet cable from your computer's LAN port to one of the router's LAN ports, correct? The initial flashing will not work properly wirelessly.

DD WRT V24 SP2 BRIDGE SETUP MOD

Sorry, I can't tell, so did you successfully flash firmware on it? It sounds like you do have some sort of Tomato firmware running on it, but are having trouble flashing DD-WRT through the Tomato interface? I was able to flash Toastman's Tomato mod on the first try, not quite sure if DD-WRT is harder to flash on this router. I still do not get dd-wrt working on my Asus RT-N66Uĭo you know what I am doing wrong? Any help you guys can provide would be greatly appreciated! Thanks in advance. ( the router status leds was like in the step B) (the router status leds was like in the step A) (only leds of "ON" and network lan are illuminated. I did the step 4 again with the big firmware from DD-WRT (I waited always after flashing more than 20min.) And the router does not boot. I got the same problem of the screenshot in the point 4, but when the process was close to 74% more leds become illuminated, such us on led, network led, wireless 2,ghz led and wireless 5ghz led.ĩ) what I am doing wrong? I really do not know. ) in flash modus (see point 2) I got what the following screenshot shows, but noting works.ħ) If I do the step 2 again and I try to get into the router the firmware called " " ) on my browser and I got a Time Out.Ħ)If I try with the same link (. Here the error: (but in the point 7 with tomato firmware and same error works, therefore I guess that error is not so important)ĥ) I try to open the following link (. The transmission of the firmware gets OK! but at the end of the process I got this error: (see screenshot below:)

DD WRT V24 SP2 BRIDGE SETUP SOFTWARE

I am going to try to explain as best as I can what I did till now on my "target" to get dd-wrt working.ġ) I have configured my network manually ( see the screenshot below)Ģ) Holding the reset botton with out energy cable, connect energy cable and switch on the router with the reset botton pressed till the "on" led blinks slowly.ģ) Upload the firmware with the tool called "firmware restoration" included in CD from the Asus router on the software "ASUS RT-N66U software utilities".Ĥ) I've try to upload the Asus RT-N66U Firmware: Image for initial flashing dd-wrt.v24-18702_NEWD-2_K2.6_mini_x 3,29 MB

DD WRT V24 SP2 BRIDGE SETUP INSTALL

I could install Toamto's firmware, but as far as I know does not match my needs. Therefore I have buy an Asus RT-N66U.Īs my target is do the same with the Asus as I do with my old Linskys using DD-WRT, but I cannot get DD-WRT on my Asus RT-N66U.

I am repeating his signal on my flat with my old router (linksys wrt54gl) which actually uses DD-WRT v24.Įverything works fine, but I want to have more speed on my LAN network, such us wireless N and 1Gbps wired lan. I hope we can solve my problem, and I am sure some users will learn something interesting here.Īctually my neighbour is sharing his WiFi with me.